Thank you very much for buying the sensor soap dispenser. In order to ensure the proper installation and use, please read the following instructions carefully. Improper installation or use may cause a malfunction and/or void the warranty.
PRODUCT FEATURES
(1) Touch-less faucet type soap dispenser
(2) Chrome plating brass body
(3) Anti-backflow device
(4) One button quick filling/recycle the soap from the tube
(5) Adopting professional moisture resistance sealant
(6) Adopting international brand-name electronic components
(7) Independent R&D soap pump with multiple anti-blocking measures
TECHNICAL PARAMETERS
Power supply | AC100V-240V |
Power consumption | Standby≤2W;Working≤5W |
Sensing distance | 5-22cm |
Soap volume | 0.6-2.0ML/time |
Bottle capacity | 1000ML |
Ambient temperature | 1-55℃ |
Suitable soap PH | 5-9 |
Suitable soap viscosity | 1-17cps |
PRODUCT STRUCTURE
INSTALLATION DIAGRAM
INSTALLATION
(1) Install the faucet body
a. Insert the faucet body in the central hole of the basin.
b. Put the sensor wire, adapter wire and the liquid tube through the rubber washer and the nut, then fix the faucet with the nut.
(2) Install the control unit
a. Put the control unit bracket on the wall and use a pencil to mark the positioning holes. Use the impact drill to drill two mounting holes and push the plastic wall plug into the mounting holes, locking the control unit bracket on the wall with the M4×25mm screws.
b. Pour the liquid soap into the bottle, and tighten it to the control unit. (Please refer to < Technical parameters> for soap requirements)
(3) Connect the tubes and wires
a. Connect the black plug between faucet and control unit, be sure to lock the plug.
b. Install the power adapter in a suitable position on the wall, and pay attention to waterproof measures.
c. Connect the red plugs between the faucet and adapter.
d. Connect the soap tubes as shown below:
(5) Debug after installation
a. Within 20 seconds after switching on the power supply, the product will automatically adjust the sensing distance according to the environment. Please do not put anything in front of the sensor.
b. Press the button on the control unit once, and the liquid soap will quickly fill up the empty liquid tube
c. Put your hands within the induction range, the faucet will automatically spew soap once.
USE INSTRUCTION
(1) When first using or refilling the soap, press the button on the control unit can achieve quickly fill up the empty liquid soap.
(2) When your hand is placed within the sensing range, the faucet will spout soap once. Before the hand leaves the sensing range, there will be no soap spout again.
(3) If you need to adjust the soap volume of every spouting, please contact with the distributor.
(4) The faucet will automatically spout soap once to prevent the tube from being blocked if no use for 48 hours.
(5) Only use the specific liquid foaming soap that contains no suspended particles or micro-beads, otherwise the tube will easily be jammed and lead to product failure.
(6) If not using for a long time, please clean the bottle and liquid tube. The detail steps are as below:
a. Cleaning the soap bottle:
Pour out all the remaining soap in the bottle, and clean the bottle with clear water until no soap bubbles.
b. Cleaning liquid tube in the control unit:
①Tighten the soap bottle with clear water and press the button to quickly discharge the water, repeat the operation until the faucet is completely sprayed with clear water.
②Hold the button for more than 2 seconds, the pump will run reverse to empty the soap tube quickly.
DAILY USE AND MAINTENANCE
(1) If there is any dirt on the sensor, please clean it up in time so as not to affect the using effect.
(2) It is strictly forbidden to rinse the faucet with water, so as not to damage to the internal circuits and cause an accident.
(3) Please clean the filter net when refill the liquid soap every time. Do not remove the filter net when adding soap.
(4) If the product is not used or has not been maintained for a long time, it may not flow smoothly or be clogged. This is not covered by the product warranty. Please refer to the following steps for self-inspection and maintenance.
a.Check and clean the filter net inside the bottle
b. Check whether the white liquid tube in the foaming device is blocked by viscous soap. If yes, pull out the tube joint and squeeze out the viscous soap of the soap tube.
c. Cleaning the pump tube
TROUBLE SHOOTING
When the following faults occur in the product, it may not be caused by the failure of the product itself. Before contacting the after-sales service, please refer to the following table for inspection and elimination.
(1) Soap does not flow when hands are placed within the sensing range.
CAUSE | CHECKPOINT |
a) Suspension of power supply | -Switch on the power |
b) Soap used up | -Add liquid soap |
c) Liquid outlet blockage | -Cleaning liquid outlet |
d) There is something else in the induction range | -Remove the thing |
e) Filter net in the bottle blockage | -Cleaning filter net |
f) Liquid tube is bent | -Straighten the liquid tube |
(2) Soap liquid flow is not smooth
CAUSE | CHECKPOINT |
a) Soap viscosity is too high | -Use the special soap of electronic induction |
b) Liquid outlet blockage | -Cleaning liquid outlet |
c) Filter net in the bottle blockage | -Cleaning filter net |